PDA

Orijinalini görmek için tıklayınız : How To Make Nokia Data logging Cable



tool
16-05-2006, 09:47
So first off I’ll assume you have an ODBI/OBD0 ECU with the CN2 de-soldered.

I SUGGEST YOU USE THE NOKIA-DKU 5 CABLE available on EBAY.

Once you have that cable you will need to cut off the cell adapter part on the end. Then you will strip the cable to expose the wires. Strip off about 1 inch.

Once you stripped the shielding you will see the shield conductor (silver wires in a woven pattern shielding the other wires). Twist this shielding to make it into a single wire. There will be some type of aluminum foil surround all the wires now, remove this foil.

http://www.synoptic-tuning.com/ecucontrol/images/usbcable.jpg
http://www.synoptic-tuning.com/ecucontrol/images/stripped.jpg

Next you will strip the brown wire and solder it to the shielding conductor that you twisted into a single wire. It should look like this.

http://www.synoptic-tuning.com/ecucontrol/images/soldered.jpg

Then you will strip the orange and red wires. Then drill a hole in the side of the ECU case and feed the wire through.


I used some random wires lying around to solder to the CN2 points. This was because the USB cable wires were too thin and the one was to thick to make a good solder connection.



WARNING, COLORS ARE NOT CONSISTENT, PLEASE SEE THIS PAGE FOR ALL KNOWN COLOR COMBINATION

Then you will

Solder the Ground conductor to #1 pin on CN2

Solder the Receive Signal wire to #2 pin on CN2

Solder the Send Signal to #4 pin on CN2

http://www.synoptic-tuning.com/ecucontrol/images/solder1.jpg

As you can see I wrapped it around the ECU bar. This was done to help avoid accidentally pulling on the black wire and having to re-solder everything. This way then you pull on the wire it seems to put the pressure on the bar and not the solder point on CN2. Or you can use a zip tie.

http://www.synoptic-tuning.com/ecucontrol/images/solder2.jpg

Then of course wrap those connections with eletrical tape or use shrink wrap.

Here is the end result.
http://www.synoptic-tuning.com/ecucontrol/images/finished.jpg

tool
16-05-2006, 09:49
WARNING, COLORS ARE NOT CONSISTENT, PLEASE SEE THIS PAGE FOR ALL KNOWN COLOR COMBINATION

The modification to the cables are similar.

With the Radio Shack cable, cut off the phone connector. Strip back the shielding to expose about 1" of wire.

Strip the brown wire and connect it to the shield conductor. Solder this to pin #1 on CN2.
Strip the orange wire and solder it to pin #2 on CN2. This is the RX lead on the cable.
Strip the red wire and solder it to pin #4 on CN2. This is the TX lead on the cable.
For the no-name eBay sourced cable, the hookup is very simple:

Strip the black wire and connect it to the shield conductor. Solder this to pin #1 on CN2.
Strip the white wire and solder it to pin #2 on CN2. This is the RX lead on the cable.
Strip the blue wire and solder it to pin #4 on CN2. This is the TX lead on the cable.

tool
16-05-2006, 09:51
Also make sure you download the USB drivers from here (http://www.pgmfi.org/twiki/bin/view/Home/SoftwareTools)

Yuregi-R
16-05-2006, 10:22
Log almaya mı yarıyor, birazda kullanım alanları hakkında bilgi verirsen.
Güzel bilgi

Saygılar

tool
16-05-2006, 11:59
kabaca baktim, log alma disinda bir extrasini goremedim. ayrica kablolari direk lehimlemek yerine bu sekilde bir aparat kullanmak daha guvenli
http://www.allelectronics.com/images/gold/full/CON-244.jpg

CTG
16-05-2006, 12:29
nokia cable falan diyince..

düşünsenize symbian için program geliştiriolar..
ecu yu telefona bağlıyosun ordan ayar yapıosun falan puhahah

1.6 VTi
22-06-2006, 23:52
nokia cable falan diyince..

düşünsenize symbian için program geliştiriolar..
ecu yu telefona bağlıyosun ordan ayar yapıosun falan puhahah

hehe süper olur ya... Skyline style... Elde cep telefonu tam kalkıcan "bi saniye kardeşim hele bir max hp yi alt devirlere çekeyim de..." diye falan :P

Oz`
24-06-2006, 11:25
palm da var ;)

efe-E
27-06-2006, 20:51
cahilliime werin ne işe yarıcak acaba bu cok merak ettim

Bamby
04-08-2006, 08:58
Gosterilen ecu bildigim kadariyla benim arabanin ecu'su d16a9 icin yani.
yanlis hatirlamosam tabii
burada yapilan seyde arabanin mapping ayarlarini loglayabilme ozelligini aktif hale getirmen oluyor.
bunlari ilk gordugum sitede bayagi bi ayrintili anlatiyordu ve ayni zamanda map ayarlarinin degistirilebilecegi bi programda oneriliyordu.
bu tarz bilgileri verirken nerden alindiginida eklesek ya :)
guzel olmaz mi?
....

nosmemos
04-08-2006, 10:22
http://www.synoptic-tuning.com

Jehuty
03-01-2007, 18:33
DKU-2 var olmaz mı :)

stlegal
03-01-2007, 20:34
DKU-2 var olmaz mı :)

olmaz dedik kardeşim 5 alıcan :)

Jehuty
03-01-2007, 23:29
yaw kablo vardı ne güzel elimizde hali hazırda değerlendirelim dedik neyse abi 5se 5 alıcaz artık

Serencebey
06-01-2007, 11:37
dke-2 kurtarmıyo sanırım :)

Serencebey
06-01-2007, 11:47
acaba symbian icin bu sekılde bi veri olayı varmıkı :)

benım telefon dırek fotograf makınası gırısı barındırıyo :)

Oz`
07-01-2007, 01:18
pocket Pc için var